{"id":1913,"date":"2015-02-15T14:03:39","date_gmt":"2015-02-15T20:03:39","guid":{"rendered":"http:\/\/haveblue.org\/?p=1913"},"modified":"2015-02-15T14:03:39","modified_gmt":"2015-02-15T20:03:39","slug":"pir-foam-for-stratasys-build-trays","status":"publish","type":"post","link":"https:\/\/haveblue.org\/?p=1913","title":{"rendered":"PIR foam for Stratasys build trays"},"content":{"rendered":"

\t\t\t\tFilament is the primary consumable on Stratasys machines, but not the only one – the build trays are also considered consumable.\u00a0 On newer machines that use plastic trays, the official recommendation is to use them for only a single print, but that starts getting expensive fast, so users will wipe them down with acetone or try sandblasting them to freshen up the surface for more use.\u00a0 The old FDM series machines that I have don’t use plastic trays as a build base, but rather a foam square.\u00a0 I had already investigated alternate materials<\/a> with poor results, and John Branlund<\/a> had started to look into craft store foam instead, as it seemed to be the material to beat.\u00a0 We eventually concluded that the foam is most likely General Plastics FR-7104 modeling foam<\/a> based on the sample kits that the company provides.\u00a0 I haven’t pursued this further, however, as I can’t imagine that shipping on a 4’x8′ sheet of rigid foam could be anything close to ‘low cost’, and I have about half a dozen extra foam bases anyhow.\u00a0 However, I’ll be turning the FDM 1600 loose to be used by other Makerspace<\/a> members very soon, and I’d like to give them the ability to simply replace the foam bases as they deem necessary without burning through what I have left.<\/p>\n

Some time back, fellow Makerspace member the_digital_dentist was experimenting with various slurries and sprays<\/a> to improve part adhesion on his very large scratchbuilt 3D printer.\u00a0 I gave him a Stratasys foam base to try, and it worked like a champ (almost too well, since the ABS support doesn’t break away nearly as easily as HIPS support).\u00a0 I mentioned my woes in trying to source more of the foam, and he suggested trying the foil-sided polyisocyanurate (PIR) foam that you can find at some home improvement stores, and gave me a few pieces to try.\u00a0 I cut a 12″ square, peeled the foil from one side, and sprayed the other side with 3M 77 adhesive before pressing it onto my material testing plate.\u00a0 I put the tray into the machine and let it heat up before testing it.<\/p>\n

\"\"<\/a><\/p>\n

Unfortunately, I failed to take differential thermal expansion into consideration.\u00a0 With the chamber heated to 70 C, the foam expanded ever so slightly, buckling upwards due to the foil still being attached on the underside.<\/p>\n

\"\"<\/a><\/p>\n

I removed the foil from the underside, and lacking anything better, used a bunch of paperclips around the perimeter to secure the foam.<\/p>\n

\"\"<\/a><\/p>\n

While the PIR foam surface isn’t as smooth as the Stratasys bases, it’s ‘good enough’ for my needs and a test print went fine.<\/p>\n

\"\"<\/a><\/p>\n

The part and support removed from the PIR foam very easily with just a little tearing of the substrate.\u00a0 Overall, it’s still not quite as good as the FR-7104 foam (tears more easily and doesn’t grip as well), but for a cheap, readily available material, it’s the best thing I’ve found so far.\u00a0 The only drawback is that locally available sheets are only 1″ thick and I need 1.25″ of thickness, but shimming up the base from the bottom shouldn’t be much of an issue.\t\t<\/p>\n","protected":false},"excerpt":{"rendered":"

Filament is the primary consumable on Stratasys machines, but not the only one – the build trays are also considered consumable.\u00a0 On newer machines that use plastic trays, the official recommendation is to use them for only a single print, but that starts getting expensive fast, so users will wipe them down with acetone or […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"nf_dc_page":"","_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"_jetpack_memberships_contains_paid_content":false,"footnotes":""},"categories":[2],"tags":[],"class_list":["post-1913","post","type-post","status-publish","format-standard","hentry","category-3d-printing"],"jetpack_featured_media_url":"","jetpack_sharing_enabled":true,"_links":{"self":[{"href":"https:\/\/haveblue.org\/index.php?rest_route=\/wp\/v2\/posts\/1913","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/haveblue.org\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/haveblue.org\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/haveblue.org\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/haveblue.org\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=1913"}],"version-history":[{"count":0,"href":"https:\/\/haveblue.org\/index.php?rest_route=\/wp\/v2\/posts\/1913\/revisions"}],"wp:attachment":[{"href":"https:\/\/haveblue.org\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=1913"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/haveblue.org\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=1913"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/haveblue.org\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=1913"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}