{"id":542,"date":"2010-08-18T21:09:15","date_gmt":"2010-08-19T03:09:15","guid":{"rendered":"http:\/\/haveblue.org\/?p=542"},"modified":"2010-08-18T21:09:15","modified_gmt":"2010-08-19T03:09:15","slug":"a-splash-of-color-part-1","status":"publish","type":"post","link":"https:\/\/haveblue.org\/?p=542","title":{"rendered":"A splash of color, part 1"},"content":{"rendered":"

\t\t\t\tA few weekends ago was Frankie’s<\/a> aluminum anodizing class<\/a> at UWM. I had done a little anodizing during the open session last summer, but that was limited to single colors and I wanted to play with multicolor effects this time around. I’ve purchased a video on DIY anodizing<\/a> as well as the MoonLite<\/a> and Caswell<\/a> anodizing manuals, and have done a lot of web research on the process. While these resources cover the basics of anodizing, they say almost nothing about how to create multicolor effects (the MoonLite manual does discuss a few techniques, however). The more complex techniques appear to be closely guarded secrets, and companies like PK Selective<\/a> (who actually invented splash anodizing – a pair of good examples are here<\/a>) are not keen on discussing how finishes such as their legendary ‘thunderstruck<\/a>‘ anno is created.\u00a0 Piers Wiggett was a true master, and once he left PK, I seem to recall that their prices jumped noticeably – like magicians, anodizing artists are generally not known for revealing their secrets!<\/p>\n

Still, there’s plenty than can be experimented with, and lots of tidbits exist on Caswell’s anodizing forum<\/a>.\u00a0 By masking with vinyl tape, you can apply different colors to different areas.\u00a0 More complex and organic looking masking can be done by applying a fast-drying liquid by brush or sponge.\u00a0 Parts can be dipped into bleach or a sulfuric acid solution (which is what we used) to bleach the dyed color back out, and by slowly dipping into the dye bath or bleaching bath, you can achieve a color gradient.<\/p>\n

\"\"<\/a>
The actual anodizing bath - a combination of sulfuric acid and electricity. Obviously a bit of caution is in order. The pieces in the bath are the 2"x2" square aluminum plates we used for samples.<\/figcaption><\/figure>\n

Anodizing actually ‘grows’ a very thin (perhaps a thousandth of an inch) layer of oxide out of the base aluminum (unlike plating, in which a dissolved metal is deposited out of solution onto the substrate).\u00a0 This oxide layer is porous and can absorb certain dyes, hence the basis for the class.\u00a0 The process of dyeing\/masking\/bleaching is not unlike reverse glass painting – what you put down first will be ‘on top’, so for complicated patterns, you have to think through the procedure in reverse and plan out your steps in advance.<\/p>\n

\"\"<\/a>
Various samples on display to illustrate some of the colors and surface treatments that are possible<\/figcaption><\/figure>\n
\"\"<\/a>
Steve Krueger was on hand to assist us with our work - I really should have picked his brain a lot more about the techniques he used for all of his samples<\/figcaption><\/figure>\n
\"\"<\/a>
Taste the rainbow - Frankie had every single color from the Caswell catalog on hand for us to try<\/figcaption><\/figure>\n

Here’s some of the samples I made during class – photographs just can’t fully capture the look of an anodized piece, unfortunately:<\/p>\n

\"\"<\/a><\/p>\n

1) Dyed the piece in fluorescent yellow, then brushed on rubber cement, and did a slow dip in the pickle (the weak sulfuric acid bath we used for bleaching) for a color gradient.\u00a0 I’m not sure why the base color darkened towards the top.<\/p>\n

2) Dyed yellow 4A, then lightly sponged on Krylon clear matte spray finish, pickled and then dyed electric blue.\u00a0 I wish it was possible to get a resulting blue as vibrant as the pieces look right when you pull them out of the dye – the color is so deep and saturated that it really defies description.<\/p>\n

3) This was actually my first attempt at a gold\/blue scheme.\u00a0 I did a sponge mask on the undyed aluminum, then I taped a scrubbing pad to the piece.\u00a0 I then dripped yellow 4A and blue 4A (thickened with corn starch) through the pad, hoping for a fairly sharp color delineation, but the corn starch didn’t make for a very solid paste, so the colors faded together.\u00a0 Still an interesting effect, though.<\/p>\n

\"\"<\/a><\/p>\n

4) Brushed on rubber cement over the undyed metal, and then dripped on electric blue and fluorescent pink (again mixed with corn starch).\u00a0 I tried a few pieces with fluorescent pink, but just could never get it to take well – it always leached out when I rinsed it after the dye bath.<\/p>\n

5) Dyed fluorescent yellow, brushed on rubber cement, then dyed deep red.\u00a0 I didn’t do an intermediate pickle step, assuming that the red would still overwhelm the yellow, but this didn’t really happen.<\/p>\n

6) I sandblasted the top half and dyed the piece turquoise.\u00a0 I’m not really a big fan of blasted finishes on anodizing, as they’re very rarely done well and generally come out far too coarse (in the paintball gun world, at any rate).\u00a0 From what I recall hearing, the secret to getting a really nice ‘frosted’ type finish is to fully polish the base metal and then very lightly blast it with glass beads, not sand.<\/p>\n

\"\"<\/a><\/p>\n

7) I ran the metal through a rolling mill with a piece of plastic mesh bag wrapped around it, which provides a neat reptilian skin look.\u00a0 Dyed bronze, brushed on rubber cement, pickled and then dyed copper.<\/p>\n

8) Dyed turquoise, sponged on Krylon matte clear spray, pickled and then dyed electric blue.<\/p>\n

9) Dyed bronze, sponged on Krylon matte clear spray, pickled and then dyed olive drab.\u00a0 The olive drab dyes very quickly, probably the fastest of any of the colors I used.<\/p>\n

\"\"<\/a><\/p>\n

10) I used another plastic mesh to provide a surface finish with the rolling mill.\u00a0 Dyed violet DS, and then I used a cotton swab dipped in pickle to draw on the surface.<\/p>\n

11) This one went through the rolling mill with a torn piece of paper – it really didn’t apply a noticeable effect unless you hold the piece up to the light.\u00a0 Dyed in olive drab, brushed on rubber cement, pickled, then dyed in yellow 4A.<\/p>\n

12) This one was a pleasant surprise, as I really wasn’t sure of what I was trying to achieve.\u00a0 Dyed red bordeaux, brushed on rubber cement, pickled, brushed on another layer of rubber cement, pickled, and dyed yellow 4A.\u00a0 The colors came out nice and rich.\t\t<\/p>\n","protected":false},"excerpt":{"rendered":"

A few weekends ago was Frankie’s aluminum anodizing class at UWM. I had done a little anodizing during the open session last summer, but that was limited to single colors and I wanted to play with multicolor effects this time around. I’ve purchased a video on DIY anodizing as well as the MoonLite and Caswell […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"nf_dc_page":"","_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"_jetpack_memberships_contains_paid_content":false,"footnotes":""},"categories":[4],"tags":[],"class_list":["post-542","post","type-post","status-publish","format-standard","hentry","category-metalworking"],"jetpack_featured_media_url":"","jetpack_sharing_enabled":true,"_links":{"self":[{"href":"https:\/\/haveblue.org\/index.php?rest_route=\/wp\/v2\/posts\/542","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/haveblue.org\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/haveblue.org\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/haveblue.org\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/haveblue.org\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=542"}],"version-history":[{"count":0,"href":"https:\/\/haveblue.org\/index.php?rest_route=\/wp\/v2\/posts\/542\/revisions"}],"wp:attachment":[{"href":"https:\/\/haveblue.org\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=542"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/haveblue.org\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=542"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/haveblue.org\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=542"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}