# $Id: DEF,v 1.39 1998/06/16 21:49:37 dholzwar Exp $ # File: strata/modelers/1600/P400/T12/Z10/DEF #--------------------------------------------------------------------------# #--------------------------------------------------------------------------# # WARNING: Preset values defined by Stratasys Inc. # Any changes made to this file is at your own risk. # Stratasys Inc. will not support any changes to this file. #--------------------------------------------------------------------------# IDENT $Revision: 1.39 $ FILEUNITS INCH # units for commands in current file only { INCH | MM } MODELER 1600 {9.4 10.0 10.0} {.1 .1 .0} {1.2 .5 .0} 0.026 MATERIAL P400 {1.007 1.0} 52 TIP T12 {.005 .014} {.012 .04} {1.0 4.0} RPLEN {.003 .0005} {.055 .0012} {.10 .002} {.625 .003} {1.625 .0035} {0 .004} ACCELERATION 5 DEFL_ANGLE 30 70 110 ZIGZAG 0.07 7 WIPES ON TIP_WIPE 2 "XD121;#TW" ROLLBACK_M "CD135;#ABS RB_SF" RSSPEED 0.875 SSPEED 1.0 SPEED BASE_FAST 800 SPEED SMALL 800 DENSITY 1.05 BASE_BOTTOM_Z .015 .030 GROW ON ON OFF SHORT PD 41 20 -10 SHORT PERIMETER 0.30 0.125 0.5 SHORT RASTER 0.20 0.125 0.5 SMALL_SET_ROAD_WIDTH 0.012 INITIAL_PURGE 20 PURGE_SPEED 1000 PURGE_ROLLBACK 167 PURGE_TIP ON OOZE 0.25 # PURGE ---------------------------------------------------------------------# ## idle time between tip use (table gives purge time in seconds) ## 0 1 10 20 30 40 50 60 + (minutes) PV 1 0 1 1 1 5 5 5 5 # very dry material 0 - 0.249 PV 2 1 1 1 2 5 5 5 5 # medium dry 0.25 - 0.499 PV 3 1 1 2 2 5 5 5 5 # medium 0.50 - 0.749 PV 4 1 1 2 2 5 5 5 7 # medium wet 0.75 - 0.999 PV 5 2 2 2 2 5 5 5 10 # very wet material 1.0 - greater # PURGE END -----------------------------------------------------------------# # SETS START --------------------------------------------------------------# G 0 DEFAULT DACBa0 NO In-Out MOD -45 45 .000 .000 .050 RED 0 0.0 \ .0201 OFF .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID \ .0201 IN .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ .0201 .000 .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID YES \ .0201 .000 .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ "This set is used as a work space when moving curves. Curves may be assigned to this set if no sets are read from an SSL. Main material." G 1 Part DACBa0 NO In-Out MOD -45 45 .000 .000 .050 RED 0 0.0 \ .0201 OFF .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID \ .0201 IN .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ .0201 .000 .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID YES \ .0201 .000 .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ "All part curves assigned to this set after slicing. Optimum all-around set. Road widths 2X slice interval. Main material." G 3 PartFast DCABa1 NO In-Out MOD -45 45 .000 -.002 .050 LIGHT-RED 2 0.0 \ .0201 OFF .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID \ .0201 IN .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ .040 .000 .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID YES \ .0201 .000 .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ "Interior sections of part assigned to this set after fast option is applied. Used for building SOLID part. Raster road widths 4X slice interval. Main material." G 5 SupportFace DACBa0 NO In-Out ALT -22 -22 .005 .000 .050 LIGHT-GREEN 0 0.0 \ .0201 OFF .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID \ .0201 OFF .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ .0201 .000 .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID YESA \ .0201 .000 .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ "Interface support layer between part and support. No gap in support raster to provide good surface finish on the part. Alternate material." G 6 Support DACBa0 NO In-Out ALT 68 68 .005 .000 .050 LIGHT-YELLOW 0 0.0 \ .015 OFF .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID \ .015 OFF .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ .015 .035 .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID YESA \ .015 .000 .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ "All support curves other than interface layers. Thin roads and gaps in rasters allow for easy removal and quick building. Alternate material." G 7 SupportFast DACBa1 NO In-Out ALT -22 -22 .015 .000 .050 DARK-GRAY 1 0.0 \ .015 OFF .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID \ .015 OFF .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ .0201 .250 .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID YESA \ .015 .000 .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ "Eligible support set curves assigned to this set when fast options are applied. Widest raster gap possible for fastest build time." G 8 BaseTop DACBa0 NO In-Out ALT -32 -32 .000 .000 .050 BLUE 0 0.0 \ .0201 OFF .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID \ .0201 OFF .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ .0201 -.004 .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID YESA \ .0201 .000 .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ "Top layer of base. No raster gap provides a smooth surface for first layer of part. Alternate material." G 9 BaseFast DACBa1 NO In-Out ALT 68 68 .000 .000 .050 LIGHT-BLUE 0 0.0 \ .0201 OFF .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID \ .0201 OFF .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ .0201 .050 .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID YESA \ .0201 .000 .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ "First layers of build. These layers are extruded onto the foam foundation. Alternate material." G 21 PartXtended DCABa1 NO In-Out MOD -45 45 .000 .000 .050 LIGHT-MAGENTA 0 0.0 \ .0201 OFF .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID \ .0201 OFF .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ .015 .150 .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID YES \ .0201 .000 .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ "Irregular or surface layers are filled, where possible, with an open, crosshatch pattern. Main material." G 22 PartXHatch DCABa1 NO In-Out MOD -45 45 -.002 -.003 .050 LIGHT-MAGENTA 2 0.0 \ .0201 OFF .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID \ .0201 IN .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ .015 .150 .999 99 99 99 999 -99 999 999 99 FORW .10 SOLID YES \ .0201 .000 .999 99 99 99 999 -99 999 999 99 START .10 SOLID \ "Interior sections of part assigned to this set after fast option is applied. Used for building honeycombed interior parts. Very large gap between rasters will reduce runtime. Main material." # SET END -----------------------------------------------------------------# # PDMM START --------------------------------------------------------------# #------ CURVES ------------------------------------------------------------# # Flow D Pre Pre Start Start Shut Roll # Area O Delay Flow Flow Dis. Off Back Speed # xxxx xxx .xxx xxx xxx xxx xxx xxx xxxxx PDMM 30 2 .026 79 7 60 41 143 800 31 4 .028 79 9 60 42 143 800 32 6 .030 79 9 60 43 145 800 33 8 .032 79 9 60 44 145 800 34 10 .034 79 11 60 45 147 800 35 12 .036 79 11 60 46 147 800 36 14 .038 79 11 60 47 149 800 37 16 .040 79 11 60 48 149 800 38 18 .042 79 11 60 49 149 800 40 20 .044 79 11 60 50 149 800 41 22 .046 79 13 60 51 149 800 42 24 .048 79 13 60 51 149 800 44 26 .050 79 13 60 51 151 800 45 28 .052 79 13 60 52 151 800 46 30 .054 79 13 60 52 151 800 48 32 .056 79 15 60 52 153 800 49 34 .058 79 15 60 53 153 800 51 36 .060 79 15 60 53 155 800 53 38 .062 79 15 60 53 155 800 54 40 .064 79 15 60 54 155 800 56 42 .066 79 15 60 54 157 800 58 44 .068 79 15 60 54 157 800 60 46 .070 79 15 60 55 157 800 62 48 .072 79 17 60 55 159 800 64 50 .072 79 17 60 56 159 800 66 52 .073 79 17 60 57 159 800 68 54 .074 79 17 60 57 159 800 70 56 .075 79 17 60 58 161 800 72 58 .076 79 17 60 58 161 800 74 60 .077 79 17 60 58 161 800 77 62 .078 79 17 60 59 161 800 79 64 .079 79 17 60 59 163 800 82 66 .080 79 17 60 60 163 800 85 68 .081 79 17 60 60 163 800 87 70 .082 79 17 60 60 163 800 90 72 .083 79 17 60 61 163 800 93 74 .084 79 17 60 61 165 800 96 76 .086 79 17 60 62 165 800 99 78 .087 79 17 60 62 165 800 102 80 .088 79 17 60 62 165 800 106 82 .089 79 19 60 63 165 800 109 84 .091 79 19 60 63 167 800 113 86 .092 79 19 60 64 167 800 116 88 .093 79 19 60 64 167 800 120 90 .094 79 19 60 64 167 800 124 92 .096 79 19 60 64 169 800 128 94 .097 79 19 60 64 169 800 132 96 .098 79 19 60 64 169 800 136 98 .100 79 21 60 65 169 800 141 100 .101 79 21 60 65 171 800 146 102 .102 79 21 60 66 171 800 150 104 .104 79 21 60 67 171 800 155 106 .106 79 21 60 67 171 800 160 108 .107 79 21 60 67 171 800 166 110 .109 79 23 60 68 173 800 171 112 .111 79 23 60 68 173 800 177 114 .112 79 23 60 69 173 800 182 116 .114 79 23 60 69 175 800 188 118 .115 79 25 60 70 175 800 195 120 .117 79 25 60 70 175 800 201 122 .118 79 25 60 70 175 800 208 124 .120 79 25 60 71 175 800 214 126 .122 79 27 60 71 177 800 221 128 .124 79 27 60 72 177 800 229 130 .125 79 27 60 72 177 800 236 132 .127 79 29 60 73 179 800 244 134 .129 79 29 60 73 179 800 252 136 .130 79 29 60 74 179 800 260 138 .132 79 29 60 74 179 800 269 140 .134 79 31 60 75 179 800 277 142 .136 79 31 60 75 181 800 287 144 .138 79 31 60 76 181 800 296 146 .140 79 33 60 77 181 800 306 148 .142 79 33 60 78 181 800 316 150 .144 79 33 60 78 183 800 326 152 .146 79 35 60 79 183 800 337 154 .148 79 35 60 80 183 800 348 156 .150 79 35 60 81 185 800 359 158 .152 79 35 60 81 185 800 371 160 .154 79 37 60 82 185 800 383 162 .156 79 37 60 83 185 800 396 164 .158 79 39 60 84 187 800 409 166 .160 79 39 60 85 187 800 422 168 .162 79 41 60 86 187 800 436 170 .165 79 41 60 87 189 800 450 172 .167 79 41 60 88 189 800 465 174 .169 79 43 60 89 189 800 481 176 .171 79 43 60 90 189 800 496 178 .174 79 45 60 92 191 800 513 180 .176 79 45 60 93 191 800 530 182 .178 79 47 60 94 191 800 547 184 .181 79 47 60 96 193 800 565 186 .184 79 47 60 96 193 800 584 188 .187 79 49 60 97 193 800 603 190 .190 79 49 60 97 195 800 623 192 .192 79 49 60 98 195 800 643 194 .194 79 51 60 98 195 800 664 196 .196 79 51 60 99 197 800 686 198 .199 79 51 60 99 197 800 709 200 .201 79 53 60 100 197 800 732 202 .203 79 53 60 100 199 800 756 204 .205 79 55 60 102 199 800 781 206 .207 79 57 60 104 199 800 807 208 .210 79 59 60 105 201 800 833 210 .213 79 61 60 107 201 800 861 212 .216 79 61 60 108 201 800 889 214 .219 79 63 60 109 201 800 918 216 .222 79 63 60 110 203 800 949 218 .225 79 65 60 111 203 800 980 220 .228 79 67 60 112 205 800 1012 222 .231 79 67 60 113 205 800 1046 224 .234 79 69 60 114 205 800 1080 226 .237 79 69 60 115 207 800 1116 228 .240 79 71 60 116 207 800 1153 230 .242 79 71 60 117 207 800 1191 232 .245 79 73 60 119 209 800 1230 234 .248 79 75 60 120 209 800 1270 236 .251 79 75 60 121 209 800 1312 238 .254 79 75 60 122 211 800 1356 240 .257 79 77 60 123 211 800 1400 242 .260 79 77 60 124 211 800 1446 244 .263 79 79 60 125 213 800 1494 246 .266 79 79 60 126 213 800 1543 248 .269 79 81 60 127 213 800 1594 250 .272 79 81 60 129 215 800 1647 252 .275 79 83 60 130 215 800 1701 254 .278 79 83 60 131 215 800 END PDMM # PDMM END ----------------------------------------------------------------#